Spray foam insulation in Mulberry, FL: get up to 3 quotes from vetted local installers
Request free quotes from up to three vetted spray foam installers serving Mulberry and nearby Polk County. Below: what your climate zone means for open vs closed cell, how much insulation to ask for, Florida's energy code, and the rebates we could verify.
- Climate zone: 2A (2021 IECC)
- Attic target: R-49 (ENERGY STAR, uninsulated attic)
- State code: Florida Building Code, Energy Conservation (state-developed, 8th Edition, 2023)
- Utility rebates we verified: Tampa Electric Ceiling Insulation; Duke Energy Florida Attic Insulation Rebate
- Federal 25C credit: ended for 2026 installs
Facts last checked October 16, 2026. Sources are linked in each section.
Where we match quotes from this page
Requests from Mulberry and ZIP codes whose center is within about 20 miles of it go to our Mulberry, FL partner installers (14 ZIP codes): 33527, 33530, 33547, 33566, 33567, 33596, 33811, 33813, 33830, 33834, 33835, 33841, 33847, 33860. Outside these? Send the form anyway and we'll tell you if we can't match you.
Climate zone 2A: what it means for spray foam
Mulberry's central point is in Polk County, which the 2021 IECC county map assigns to climate zone 2A (hot-humid in DOE's Building America terms). Zone 2A is a moist ("A") zone, which drives the vapor and R-value rules below.
Other counties within our Mulberry service radius: Hardee County (2A), Hillsborough County (2A). All are zone 2A too.
Source: PNNL-33270, Guide to Determining Climate Zone by County (IECC 2021).
Open cell vs closed cell in Mulberry, FL
Attic roofline: in climate zones 1–3 an unvented ("sealed") attic with open-cell foam sprayed under the roof deck is a common way to bring attic ductwork and air handlers inside the insulated envelope. The International Residential Code (Section R806.5) allows unvented attics with air-impermeable insulation such as spray foam; for a hybrid "flash-and-fill" assembly the foam layer at the deck must be at least R-5 in zone 2A.
Humidity: in a hot-humid climate, a sealed attic becomes part of the conditioned house. Ask how the installer and your HVAC contractor will handle attic humidity (for example a small supply-air connection or dehumidification).
Closed cell earns its higher price where you need a vapor retarder or water resistance: crawlspace walls, rim joists, below-grade walls.
Metal buildings, pole barns and shops
For uninsulated metal roofs and walls, closed-cell foam sprayed directly on the panels is used both as insulation and as a vapor retarder to stop condensation from forming and dripping on the underside of the metal. When you request quotes, choose "Metal building / pole barn" and give the building's footprint and wall height; ask each installer for foam type, thickness, and whether a thermal or ignition barrier coating is required for how the building will be used. We don't have data on how common these buildings are around Mulberry, so we won't guess.
How much insulation to ask for
| Where | ENERGY STAR recommendation for zone 2A |
|---|---|
| Attic, uninsulated | R-49 |
| Attic with 3–4" of existing insulation | add R-38 |
| Floor over unconditioned crawlspace/basement | R-13 |
To reach R-49 with foam alone you'd need roughly 13.2–14.0" of open cell (about R-3.5 to R-3.7 per inch) or 7.0–9.8" of closed cell (about R-5 to R-7 per inch). Many roofline spray foam jobs are installed thinner than that and justified through the code's performance path or the unvented-attic rules, so ask every installer to write the foam type, thickness and resulting R-value on the quote and explain how it meets your local code.
Source: ENERGY STAR, Recommended Home Insulation R-Values (based on 2021 IECC). ENERGY STAR's figures are recommendations for existing homes; your local code sets the legal minimum for new work.
Florida energy code
Florida Building Code, Energy Conservation (state-developed, 8th Edition, 2023), effective December 31, 2023. Unlike the 2021 IECC, the Florida code requires R-38 ceiling insulation in climate zone 2 (instead of R-49). NAHB lists the 9th Edition as expected December 31, 2026.
Source: NAHB, "Residential Provisions of the IECC: State Adoption Status" (current as of May 2026); official state status at DOE Building Energy Codes Program.
Homes in Mulberry, FL
Census figures for Mulberry city (ACS 2020–2024 5-year estimates): about 2,066 housing units, a median year built of 1989, 25% built before 1980 and 11% built in 2010 or later. 42% are single-family detached homes and 42% are mobile/manufactured homes. 79% of occupied homes are owner-occupied, with a median owner-reported home value of $133,800.
- 98% of homes heat with electricity (furnaces, heat pumps or baseboard). Several utility insulation rebates are aimed at electric-heat or central-A/C customers, so check the programs below.
- With 42% mobile/manufactured homes, note that several utility insulation programs exclude manufactured homes. Check eligibility before counting on a rebate.
- Because Mulberry is small, these survey estimates have wide margins of error; treat them as approximate.
Rebates and incentives for Mulberry, FL
Utility programs that may apply, depending on which utility serves your address:
Tampa Electric Ceiling Insulation
Rebate per square foot of attic insulation added after a free Tampa Electric attic inspection recommends it; apply within 90 days of installation.
Read on the program's own page October 16, 2026. Programs change; confirm before you sign.
Duke Energy Florida Attic Insulation Rebate
$0.25–$0.31 per sq ft (up to $600–$800) to bring attic insulation up to at least R-38, after a free Home Energy Check, using a Duke Energy approved contractor. Manufactured homes are not eligible.
Read on the program's own page October 16, 2026. Programs change; confirm before you sign.
Florida state Home Energy Rebates
Not yet launched Florida Energy Saver Program
Electrification/appliance rebates (HEAR): "The HEEHR Pilot program is expected to launch in the future. The HEEHR full program is expected to be available to eligible Floridians after the pilot period."
Whole-home efficiency rebates (HOMES/HER): "The HEEHR and HOMES programs are expected to launch in the future."
Max rebate (per official page): A household can receive up to $14,000 in rebates.
Official source: Florida Department of Agriculture and Consumer Services. Status text compiled via referencesource.org, last checked by them September 29, 2026. Full Florida rebate page →
What spray foam costs (national published ranges)
We don't have enough local quotes for Mulberry, FL to publish local prices, and we won't make them up. These national ranges are a starting point; your installers' quotes are what count.
| Example job (typical thickness) | Estimated installed range |
|---|---|
| 1,000 sq ft attic roofline, open cell (6") | $3,600–$9,600 |
| 1,000 sq ft attic roofline, closed cell (3") | $3,900–$9,300 |
| 1,500 sq ft walls, open cell (3.5") | $3,150–$8,400 |
| 1,500 sq ft walls, closed cell (2") | $3,900–$9,300 |
| 200 sq ft rim joists, closed cell (2") | $520–$1,240 |
Board feet × Angi's 2026 installed price per board foot. Angi reports a national average spray foam project of $2,888 (typical $1,455–$4,337). Check a quote you already have →
Questions to ask each installer
- Foam type, brand, thickness and resulting R-value for each area, in writing.
- Which climate zone and code edition they're designing to.
- Whether removal of old insulation, air sealing, and any required ignition/thermal barrier coating are included.
- Whether they participate in Tampa Electric Ceiling Insulation or the other programs above, and who files the paperwork.
- Whether they'll do (or coordinate) combustion safety testing if you have gas appliances.
FAQ
What climate zone is Mulberry, FL in?
Polk County is IECC 2021 climate zone 2A, per PNNL's county list (PNNL-33270).
Should I use open-cell or closed-cell spray foam in Mulberry, FL?
For attic rooflines in zone 2A, open cell is common and code-permitted in unvented attics; closed cell is worth the premium for crawlspace walls, rim joists and metal buildings.
How much attic insulation do homes in Mulberry, FL need?
ENERGY STAR recommends R-49 for an uninsulated attic in zone 2A (or adding R-38 on top of 3–4 inches of existing insulation). Florida's code: Florida Building Code, Energy Conservation (state-developed, 8th Edition, 2023).
Are there spray foam or insulation rebates in Mulberry, FL in 2026?
The federal 25C tax credit does not apply to insulation installed after December 31, 2025. Utility programs that may apply, depending on which utility serves your address: Tampa Electric Ceiling Insulation; Duke Energy Florida Attic Insulation Rebate. Florida's state Home Energy Rebate program status: Not yet launched.
How much does spray foam cost in Mulberry, FL?
We don't publish local prices until we have enough real local quotes. National published ranges are about $0.60–$1.60 per board foot for open cell and $1.30–$3.10 for closed cell, installed (Angi, 2026), and many companies have a $1,000–$2,000 minimum.
How does requesting quotes work?
Fill in the form once. We pass your request to up to three vetted partner installers who serve Mulberry, FL, and they contact you to schedule an estimate. It's free and there's no obligation.
Other areas we serve in Florida
Lakeland · Tampa · Orlando · Port St. Joe · Panama City Beach · All Florida service areas · All service areas